ACT HANDKEY II Betriebsanweisung Seite 1

Terminal User’s GuideHK-II

Introduction6HandKey units have the following options available.• Backup Battery Support See Technical Note 70200-0012 rev C• Modem Communication

7Planning an InstallationBefore you begin installation, check the site blueprints, riser diagrams, and specifications for important information about t

Planning an Installation8Four basic circuits typically connect to the HandReader:• Power Input• Door Control Inputs and Outputs• Networking and Com

HandKey II Manual9two pins protruding up from the main logic board are not connected to each other. This effectively opens the circuit, removing the b

Planning an Installation101 2 3 4 5 6 7 8 9 10 12 13 141234567891011121314OUTPUTSREX SWITCHDOOR SWITCHGROUNDAUX IN 1GROUNDGROUNDAUX IN 2CLOCK/D1LOCK O

HandKey II Manual11For systems with multiple units on a network, there will be a series of cables daisy-chained between the units, and the shield of e

Planning an Installation12However, the power supplies must be truly floating, with no hidden paths back to the high-voltage side of the transformers, o

HandKey II Manual13An open collector transistor driver drives each one of these outputs. Open collector refers to a transistor configuration capable of

Planning an Installation14

15Networking and CommunicationsHandReader networking and communications can be configured in one of five ways:• as a stand-alone HandReader• as a mast

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits ar

Networking and Communications16Typically, HandReader networks link to a PC using an RS-422 connection. These networks have the following requirements.

17Mechanical InstallationSelect an installation location based on the guidelines provided in the Planning an Installation section beginning on page 7.

Mechanical Installation185. For a solid wall, hold the wall plate against the wall, centering the leveling hole over the mark in the wall.6. Align a

HandKey II Manual191. Remove the HandReader from its carton.2. Align the sleeves of the back plate with the pins of the wall plate and slide the Han

Mechanical Installation20With the wall mount latch in the unlocked position, swing the body of the HandReader up and rotate the key away from the wall

21Wiring ConnectionsOnce the HandReader is attached to the wall plate the wiring connections to the HandReader can be made (see Figure 5-1). WALLSeria

Wiring Connections22Table 7-1: TS-1 - Power and Communication ConnectionsTerminal Connection15 RS-422 Rx- or RS-485 Rx-/Tx-16 RS-422 Tx- or RS-485 Rx+

HandKey II Manual23* These components are not supplied by Schlage Biometrics, Inc.TOP OF THEHAND READERHINGEWALL TO WHICHTHE HAND READERIS ATTACHEDAUX

Wiring Connections24* These components are not supplied by Schlage Biometrics, Inc.TOP OF THEHAND READERHINGEWALL TO WHICHTHE HAND READERIS ATTACHEDAU

HandKey II Manual25TOP OF THEHAND READERHINGEWALL TO WHICHTHE HAND READERIS ATTACHED12 to 24 VAC/DCInput14 1312111098 7 6 5 43 2118 17 1615RS-422Conne

iiiTable of ContentsIntroduction 3HandKey II 3Biometrics 3Principle of Operation 3The HandKey II 3Specifications 5Options 6UL Compliance 6Plann

Wiring Connections26546F1879F20NoNoEnter213Clear*#Yes18171615 TS-1Master18171615TS-1Remote 118171615TS-1Remote X4-WireRS-422ConnectionRx -Rx +Tx -Tx +

HandKey II Manual27MasterRemote 1Remote X2-WireRS-485Connection2-WireRS-485ConnectionRx/Tx -Rx/Tx +2-WireRS-485ConnectionRx/Tx -Rx/Tx +Rx/Tx -Rx/Tx +1

Wiring Connections2818171615TS-1Remote18171615TS-1Remote18171615RS-422ConnectionTS-1RemoteDB-25SerialPortRx -Rx +Tx -Tx +RS-422ConnectionRx -Rx +Tx -T

HandKey II Manual29* These components are not supplied by Schlage Biometrics, Inc.WALL TO WHICHTHE HAND READERIS ATTACHEDTOP OF THEHAND READERHINGE12

Wiring Connections30

31Erasing the MemoryThere are two options when erasing the memory of the HandReader.1. Setup2. AllThe erasing of the setup will set the HandReader’s

Erasing the Memory32

33Enter a Command MenuPress the Clear and Enter keys simultaneously to enter a command menu.1. The display appears as follows.ENTER PASSWORD2. Press

Enter a Command Menu341. The display appears as follows.ENTER PASSWORD2. Enter your ID number on the keypad and place your hand on the platen for ve

35Programming the HandReaderThe HandReader is programmed via a series of command menus. A summary of the menus and commands is given in Table 6.Table

Wiring Connections 21ivWiring Connections 21Wiring Examples 21Erasing the Memory 31Erasing HandReader Memory 31Enter a Command Menu 33If No One

Programming the HandReader36A second method for controlling access to the command menus is through the use of Authority Levels. Authority Levels contr

HandKey II Manual37Once a HandReader network is in operation the following commands are used to manage and maintain the HandReader network.1. Set Rea

Programming the HandReader38

39Service MenuThe Service Menu commands provide information that helps you determine if the HandReader is operating properly and within normal operati

Service Menu40The Calibrate command verify that the HandReader’s exposure values are within normal operating parameters. The normal operating paramete

41Setup MenuThe Setup menu commands allow you to set the basic operating parameters for the HandReader.Once in the Setup menu you can step through and

Setup Menu42Table 12-8: Setup Command MenuSetup MenuPassword = 2Set Language Select LanguageSet Date Format Select Date FormatSet Ti

HandKey II Manual43The Set Language command allows the language shown on the HandReader’s display to be “localized” for a variety of countries. The de

Setup Menu44Set the ID Length to the number of digits in the longest ID number. This command is unnecessary (and should be left at its default value)

HandKey II Manual45In HandReader networks, one HandReader must be set as a Master HandReader and all remaining HandReaders must be set as Remote HandR

HandKey II ManualvData From Network 48Data To Network 48Enrollment Menu 49Preparation 49User Education 50Proper Hand Placement 50Left Hand Enrol

46

47Management MenuThe Management menu commands allow you to manage employee data stored in a HandReader.Once you have entered the Management menu, ther

Management Menu48The Data from Network command allows the master HandReader to receive information from a HandReader on the network. This is used to t

49Enrollment MenuEnrollment is the process of recording a hand image and associating it with an ID number. The first person to enroll in the HandReader

Enrollment Menu50The HandReader is easy to use and non-threatening. However, most people have never used a biometric HandReader. Training users on how

HandKey II Manual51When a user uses the HandReader a number appears in the display.ID VERIFIED##The number on the display reflects how accurately the u

52

53Security MenuThe commands in the Security menu control the security of the information within the HandReader and the sensitivity of the HandReader w

Security Menu54Table 15-12: Security Command MenuSecurity MenuPassword = 5Set User Data Set User Authority Level (Y/N) ID

HandKey II Manual55The Set User Data command allows you to set the User Authority level, the User Reject Level, and the User Time Zone.• The Authorit

Appendix D: Troubleshooting Guide 79viErasing the HandReader Setup and User Database 77Appendix D: Troubleshooting Guide 79Display Messages During

Security Menu56Use the Reject Threshold command to set the HandReader’s reject sensitivity level applied when reading hand data and to set the number

57HandReader MaintenanceA minimum amount of system maintenance is required to keep HandReaders fully functional. HandReaders should be cleaned periodi

HandReader Maintenance58

59Appendix A: Tips for a Successful InstallationUnless the following tips are followed, the installation runs the risk of having some level of difficul

Appendix A: Tips for a Successful Installation60Bad enrollments equal bad verification (meaning scores will be too high). The key to successful verifica

61Appendix B: Noted Board Configuration Differences Because of Schlage Biometrics’ camera retrofit of the HandReader some changes have been made to the

Appendix B: Noted Board Configuration Differences 62Number OLD PCB Number NEW PCB 1 12-24 VDC (+) OR VAC 1 (+) 5 VDC OUTPUT 2 12-24 VDC (-) OR VAC 2 DA

HandKey II Manual63134562810912713111415171619182421232022262511617181521913141011124567823J6 - 2 pin PowerconnectorTS2 - 6 pin InputconnectorTS1 - 4

Appendix B: Noted Board Configuration Differences 641. To reset the memory of the HandReader follow these steps-2. Remove power and battery jumper, i

65Appendix C: Old Board Configuration InformationWall Plate Installation1. Loosen the three bottom mounting screws until there is approximately 1/8 in

3IntroductionThe HandKey II is Schlage Biometrics’ fourth generation biometric access control HandReader1. The HandReader records and stores the three

Appendix C: Old Board Configuration Information66Wiring ConnectionsOnce the Hand Reader is attached to the wall plate the wiring connections to the Han

HandKey II Manual677 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 267891011121314151617181920212223242625SWITCH INPUTS OUTPUTSCARDREADERINPUTRE

Appendix C: Old Board Configuration Information68Table 19-13: TS-1 - Power and Communication ConnectionsTerminal Connection1 Power Input 12 to 24 VDC/V

HandKey II Manual6926 25 24 23 2221 20 19 18171615 14 13 12 11 109 876 5 43 214-WireRS-422Connection12 to 24 VAC/DCInput+-* These components are not s

Appendix C: Old Board Configuration Information7026 25 24 23 2221 20 19 18171615 14 13 12 11 109 876 5 43 214-WireRS-422Connection12 to 24 VAC/DCInput+

HandKey II Manual7126 25 24 23 2221 20 19 18171615 14 13 12 11 109 876 5 43 214-WireRS-422Connection12 to 24 VAC/DCInput+-* These components are not s

Appendix C: Old Board Configuration Information72654321TS-1Master654321TS-1Remote 1654321TS-1Remote X4-WireRS-422Connection12 to 24 VAC/DCInput+-Rx -Rx

HandKey II Manual73654321TS-1Master654321TS-1Remote 1654321TS-1Remote X2-WireRS-485Connection12 to 24 VAC/DCInput2-WireRS-485Connection12 to 24 VAC/DC

Appendix C: Old Board Configuration Information74546F1879F20NoEnter213Clear*#YesNoRecognition Systems Inc.654321TS-1Remote546F1879F20NoEnter213C

HandKey II Manual7526 25 24 23 2221 20 19 18171615 14 13 12 11 109 876 5 43 21RS-422Connection12 to 24 VAC/DCInput+-* These components are not supplie

Introduction4546F1879F20NoEnter213Clear*#YesNoRecognition Systems Inc.PLATEN AND GUIDE PINSHANDPLACEMENTDISPLAYLCD DISPLAYFUNCTIONKEYSVERIFICAT

Appendix C: Old Board Configuration Information76Setting the DIP SwitchesDIP Switch settings perform three tasks for the Hand Reader (see Figure 17-11)

HandKey II Manual77Communication can be done via an RS-232 direct connection, a 4-wire RS-422 network configuration. The factory default setting is for

Appendix C: Old Board Configuration Information78Closing the HandReaderBefore closing the Hand Reader, ensure dip switches 4 and 5 are OFF (refer to Fi

79Appendix D: Troubleshooting GuideVarious messages can appear on the HandPunch’s display during hand verification. These messages are defined in.Table

Appendix D: Troubleshooting Guide80The HandPunch’s beeper and LED status display also display hand verification information. This information is defined

81GlossaryAddress, IP – An Internet Protocol address is a unique address assigned to a computer for communicating over the Internet. It is made up of

Glossary82Transaction – A Transaction is any kind of event recorded at a Hand Reader. Transactions may include actions such as accepted or denied hand

83Limited WarrantySchlage Biometrics, Inc. (the “Company”) warrants to the original user the products manufactured by the Company (the “Product”) to b

www.schlage.com Ingersoll Rand’s Security Technologies Sector is a leading global provider of products and services that make environments safe, secur

HandKey II Manual5Size: 8.85 inches wide by 11.65 inches high by 8.55 inches deep (22.3 cm)22.3 cm wide by 29.6 cm high by 21.7 cm deepPower: 12 to 24